3 steps windlass rod tourniquet

CAT Resources – Inventor and Exclusive Manufacturer of the ...

C•A•T Resources is the inventor and exclusive manufacturer of the Combat Application Tourniquet ... Windlass Rod. Increased diameter, enhanced strength, ...

ROUTE band around limb, and through routing buckle. 07. TWIST the windlass rod until bleeding has stopped (complete steps. 1-6 in under 1 ...

Step 2: Twist the Windlass Rod™ until the bleeding stops. Step 3: Secure the rod and band with the Windlass Strap™M. Another critical design characteristic is ...

Step 3 - Coagulation ... (4) Lock the windlass rod in place with the clip. C-A-T Tourniquet Use. 68W Combat Medic. Page 27. 10/3/2010. 27.

Tighten windless rod or tensioning device until distal bleeding is stopped. ... Reassess every 2-3 min for additional bleeding, tighten or apply a second ...

Life-Threatening Bleeding + Tourniquet Application Kit

... Tourniquet with windlass rod and student First Aid Training Pack. The First ... (3) · Life-Threatening Bleeding + Tourniquet Application Kit · $31.95. Reviews. The ...

Any thinner and it could do more damage and would be ineffective in stopping blood flow. Good examples of a windlass are: scissors, stick, metal rod, dinner ...

The next step is to grasp the backplate and windlass rod in your hand (this is what you will slide underneath the back of the knee first) and ...

Step 3: Adjust the tourniquet. Be sure the tourniquet is at least 2-3 inches ... Step 5: Use the windlass rod to further tighten the tourniquet.

To make a homemade tourniquet more effective, make an improvised windlass by placing a rod-like item in the tourniquet knot and twisting it. Items that can ...

SOF® Tourniquet

This is a critical step for proper tourniquet application and results in fewer windlass rotations required to reach occlusion. 3) Rugged Buckle. Engineered to ...

Pull the tourniquet tight through the snap-lock buckle. 3. Twist the windlass rod until the haemorrhage has ceased. If haemorrhage is not controlled ...

STEP 3. Twist the rod until bleeding has stopped. Also check for distal pulse beneath the tourniquet near the wound,this should disappear.

Note: The tourniquet application steps described below ... For added security and always before moving the patient, the provider secures the windlass rod with the ...

Secure the windlass to keep the tourniquet tight and in place. Note the time – as best you can – of when the tourniquet was applied, some tourniquets may have a ...

How to Apply a Tourniquet: 9 Steps (with Pictures)

Applying the Tourniquet · Step 1 Select an appropriate material. · Step 2 Apply the tourniquet between the heart and injury. · Step 3 Use a stick ...

A tourniquet requires some form of mechanical assistance such as a windlass rod ... If the rescuer has to turn the rod more than 3—4 times, then ...

WHEN EVERY SECOND COUNTS · 1. Single Routing Buckle · 2. Windlass Rod · 3. Windlass Clip · 4. Windlass Strap · 5. Stabilization Plate · 6. Free-Moving Internal Band.

Joints protect blood passageways and will not allow you to apply pressure on an artery. Step 5: Use the windlass rod to further tighten the tourniquet. Twist ...

Performance Steps: 1. Remove the C-A-T from the carrying pouch. 2. Slide the ... Twist the Windlass Rod until the bleeding stops. When the tactical situation ...

How to Apply a Tourniquet Correctly

Step 5: Tighten the Tourniquet. Tighten the tourniquet around the limb by twisting the windlass. Keep an eye on the bleeding and take note of ...

In this video, Army combat medics demonstrate how to apply a two-handed windlass tourniquet (TQ) in the Tactical Field Care phase of TCCC. ... The three phases of ...

Take any of the left over tail of the band and secure it in the windlass clip. Then secure the tail and the windlass rod with the securing strap ...

- Aluminum windlass rod. - Application remains the ... Insert the injured limb through the loop in the band and position tourniquet 2-3" above the bleeding site.

• Twisting the windlass rod more than 3 times may cause it to break. • If you can twist the windlass rod more than 3 times, repeat steps 2-4 and pull the Omni-.